Zebra ZE500 Podręcznik Użytkownika Pobierz pdf (Strona 68)

Printer Setup and Operation

Load Ribbon and Media

P1051584-002 8/23/12

15. Raise the peel roller latch so that the peel roller assembly pivots downward.

16. Thread the liner around the peel bar, under the platen roller, and through the peel roller

assembly.

LH RH

Important • If the applicator has an air tube, route the liner between the air tube and the

peel bar. Do not thread the liner over the air tube.

LH RH

1 2 ... 63 64 65 66 67 68 69 70 71 72 73 ... 169 170

User Guide 1
DECLARATION OF CONFORMITY 3
Compliance Information 4
Contents 5
About This Document 9
Who Should Use This Document 10
Contacts 11
Document Conventions 12
Introduction 13
Print Engine Orientation 14
Print Engine Components 15
POWER PAUSE STATUS DATA 16
Default Password Value 20
Control Panel Display 21
• the non-resettable counter 26
3. Do you want to continue? 28
PERMANENT 36
Types of Media 39
Printer Setup and Operation 40
Ribbon Overview 41
Adhesive Test 42
Ribbon Scratch Test 42
Printer Setup and 43
Operation 43
Handling the Print Engine 44
Remove the metal spacer 46
To Store the Print Engine 47
To Ship the Print Engine 47
Print Engine Installation 48
9.648 in 50
(245 ± 0.1 mm) 50
0.445 in 50
(11.3 mm) 50
16.62 in. (422.1 mm) 51
Data Cables 58
115 V AC 59
230 V AC 59
Power Cord Specifications 60
Load Ribbon and Media 62
Loading Media 65
19. Close the media door 69
Printer Configuration 71
Adjustment 71
Changing Printer Settings 72
Print Settings 73
Applicator 75
• ZE500-4 203 dpi: 832 dots 77
• ZE500-4 300 dpi: 1228 dots 77
• ZE500-6 203 dpi: 1344 dots 77
• ZE500-6 300 dpi: 1984 dots 77
~JS when received 79
• ENABLED 80
• DISABLED 80
Directory Listing 88
Network Settings 89
Print Server Settings > 92
Print Server Settings 92
Language Settings 93
• ZPL II 94
Sensor Settings 95
Port Settings 96
ZEBRA response messages are 98
ZEBRA is selected, the print 98
DSR/DTR for host 98
LOAD BACKING 99
P1051584-002 8/23/12 100
REMOVE RIBBON 101
CALIBRATING 101
PLEASE WAIT 101
RELOAD ALL 101
Close the media door 102
Remove Used Ribbon 103
Adjust the Sensors 104
Reflective Media Sensor 105
Ribbon Sensor 105
Toggle Positioning 106
I) the printer.) 107
Printhead Pressure Adjustment 108
Routine Maintenance 111
CLEAN HEAD NOW appears 112
Clean the Media Compartment 113
7. Close the media door 114
Lubrication 115
Troubleshooting 117
Printing Issues 118
Ribbon Problems 121
Error Messages 122
1) is likely 123
O) the print engine 124
I) the print engine 124
Display/ 126
Print Engine Condition 126
Communications Problems 127
Miscellaneous Issues 128
Print Engine Diagnostics 130
CANCEL Self Test 131
PAUSE Self Test 132
FEED Self Test 133
Print Quality Description 134
FEED + PAUSE Self Test 136
CANCEL + PAUSE Self Test 136
FE indicates a framing error 137
PE indicates a parity error 137
NE indicates noise 137
Sensor Profile 138
MEDIA (3) for the media 139
Specifications 141
General Specifications 142
Printing Specifications 143
Ribbon Specifications 143
Media Specifications 144
Applicator Interface Board 145
Reconfiguration 145
Remove Power and Data Cables 146
) off of the print engine 147
8/23/12 P1051584-002 149
The installation is complete 155
Glossary 157
8/23/12 P1051584-002 161

Komentarze do niniejszej Instrukcji

Brak uwag

Zebra ZE500 Podręcznik Użytkownika Strona 68

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Drukuj i skanuj Zebra ZE500