Zebra TTPM3 Dokumentacja Strona 105
- Strona / 112
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
104
Specifications
Document Stock
01/06/2009 TTPM3 Installation and Programming Manual P1003642-001
Figure 22 • Stub Perforation to Create a Tear-off Tab,
Perforation for Stub Placed at Trailing End of the Ticket
Tickets with 45° Cut Corners
Some applications are using tickets with cut corners without radius. These tickets are not
within the specifications for use in the TTPM3 printer series. The effect will be that the ticket
detection point moves about 1.3 mm, not only causing incorrect cut but also erroneous
placement of the magnetic code.
The coding starts 1.3 mm too early resulting in synchronization zeroes being lost in the
beginning of the ticket. On units configured for center track, the ticket should be readable in
both directions. If synchronization is lost, the tickets will be readable if inserted one way, but
not the other way around.
A solution to this problem is using HEX code for the magnetic message instead of ISO code.
Thus you can compensate for the lost synchronization zeroes by adding additional
synchronization zeroes in the beginning of the message. However, note that HEX encoded
tickets are normally not readable in standard ISO-card readers.
Figure 23 • Ticket Position is Erroneously Detected with 45° Corners
Min. 85.6 mm
Transport
direction
Ticket viewed from bottom (magnetic stripe side)
6 mm
Perforation not allowed within this 6 mm wide area
Ticket
movement
mm specified radius
mm trigger point movement with cut corners
1.3
3.18
SW97115
- Zebra® TTPM3 1
- Installation and 1
- Programming Manual 1
- Contents 3
- Document Printing 8
- Magnetic Encoding 8
- Document Handling 8
- Introduction 10
- Contacts 10
- Installation 11
- Installing a Desktop Printer 13
- Output Tray or Nozzle? 15
- Socket: AMP No. 350689-1 17
- Operation 19
- Keyboard 20
- Paper Stock Positioning 21
- Paper Loading 22
- Paper Jam Removal 23
- Self Test 24
- Repeat Fixed Print 24
- TTPM3 Start-up 25
- Power Failure Cleanup 25
- Start-up Synchronization 25
- Normal Operation 26
- Single-ticket Handling 27
- Inserting a Single Ticket 28
- Read and Decode 28
- Encode and Print 29
- Ejecting the Ticket 29
- Programming 31
- Graphics 33
- Bar Codes 34
- Magnetic Codes 34
- Triggering a Printout 35
- Command Acknowledgment 35
- Additional Commands 35
- Ticket Memory 35
- Encode Binary Data on Track 1 36
- System Commands 37
- Document Entry Commands 38
- Print-data Commands 38
- Storage Commands 39
- Command Reference 41
- !Z 20 <CR><LF> 44
- Feed- acceleration and speed 45
- Example • 45
- Error code Error 47
- Print Related Commands 49
- Text Printing 50
- Graphics Printing 51
- Printing Bar Codes 53
- Example 2 • Code 39 example 54
- Example 3 • Code 128 example 54
- Canceling a Ticket 55
- Encoding 57
- Checksum 59
- Reading and Decoding 60
- What Can You Encode? 61
- Font Loading 68
- Logotypes 69
- Ticket Examples 70
- Printing Bold Text 73
- Reversed Text 73
- Text Attributes 74
- Default Parameter Settings 75
- Default Value 76
- Examples 76
- Summary of Parameter Settings 77
- Restore Factory Default 78
- Parameter Reference 79
- Sets burn time 27 80
- Silent 80
- Enabled 80
- Sets 400 steps/second 82
- Sets 4000 steps/second 82
- Sets 1000 steps/second 82
- Error Codes and Status 87
- Reporting 87
- ENQ” (05H), and !S commands 88
- Security Additions 89
- Extended acknowledgement 91
- Maintenance 93
- Fault Finding 94
- Cleaning the Print Head 95
- Firmware 95
- Setup Options 98
- Communications Protocol 98
- Communications Cable 99
- Ticket Base Material 100
- Coating and Preprint 101
- Magnetic Media 101
- Document Stock 102
- Specifications 102
- TTPM3 Accepted Sizes 103
- Equal Distance Between Tabs 104
- Tickets with 45° Cut Corners 105
- Firmware Versions 106
- Firmware History 106
- FW Version TTPM2 TTPM3 106
- FW revision Change 106
Powiązane produkty i podręczniki dla Drukuj i skanuj Zebra TTPM3
Drukuj i skanuj Zebra EM 220 Dokumentacja
(67 strony)
(67 strony)
Drukuj i skanuj Zebra 105Se Dokumentacja
(110 strony)
(110 strony)
Drukuj i skanuj Zebra CPCL Dokumentacja
(70 strony)
(70 strony)
Drukuj i skanuj Zebra TTPM2 Dokumentacja
(140 strony)
(140 strony)
(86 strony)
Drukuj i skanuj Zebra CPCL Dokumentacja
(497 strony)
(497 strony)
Drukuj i skanuj Zebra MZ series Dokumentacja
(53 strony)
(53 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.023 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji