Zebra TTPM3 Dokumentacja Strona 90
- Strona / 112
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Error Codes and Status Reporting
Errors
89
P1003642-001 TTPM3 Installation and Programming Manual 01/06/2009
Errors
TTPM3 reports error conditions in the form of error codes. An error condition is reported as a
NAK (15H) followed by a one-character error code. The error codes have been defined,
starting with ASCII character "1" (31H) according to the following table:
"1" No paper in the entry path selected with
!L1, !L2, !L17, or !L18.
"2" Paper jam when executing
!L1, !L2, !L17, or !L18.
"3" Reserved.
"4" Cutter error. No full cut performed. Cutter blade returned to home position by
reversing the cutter motor.
"5" Cutter error. Cutter blade not returned to home position.
"6" Cutter error. Cutter blade not moving. If this error code is received immediately
after power ON, it indicates that something is wrong with the +24V supply.
"7" Paper jam when executing the !P command.
"8" Magnetic encoding on track 2 (or center track) failed.
"9" Magnetic encoding on track 1 or 3 failed.
"A" Not possible to read magnetic information with
!D, !D1, !D2, or !D3 commands.
”B” No document inserted within time limit following an
!L3 command (front load).
”C” Document inserted (front load) but immediately retracted.
”D” Document inserted through front load is blocked.
”E” Document blocked in the front load input feeder during an
!L3 command. Also
used when combining the characters | and } in a hex magnetic string to get normal
behavior if the encoding was successful. If an error occurs then the ticket is
transported back to the start position and
NAK E is sent.
“G” Document found in the ticket path during power on has been erased, VOID-
printed and ejected.
“P” If !P is sent to the printer and paper is out, it replies with NAK P and discards data.
"X" Critical error. This is issued when the printer must be turned off, error condition
cleared, then turned off again.
Note • For TTPM3 to send ACK, or NAK + error codes, the DIP-switch 6 on the TTPM3
control board must be set to ON. Position OFF places the unit in a silent mode preventing
these codes from being transmitted to the host computer.
- Zebra® TTPM3 1
- Installation and 1
- Programming Manual 1
- Contents 3
- Document Printing 8
- Magnetic Encoding 8
- Document Handling 8
- Introduction 10
- Contacts 10
- Installation 11
- Installing a Desktop Printer 13
- Output Tray or Nozzle? 15
- Socket: AMP No. 350689-1 17
- Operation 19
- Keyboard 20
- Paper Stock Positioning 21
- Paper Loading 22
- Paper Jam Removal 23
- Self Test 24
- Repeat Fixed Print 24
- TTPM3 Start-up 25
- Power Failure Cleanup 25
- Start-up Synchronization 25
- Normal Operation 26
- Single-ticket Handling 27
- Inserting a Single Ticket 28
- Read and Decode 28
- Encode and Print 29
- Ejecting the Ticket 29
- Programming 31
- Graphics 33
- Bar Codes 34
- Magnetic Codes 34
- Triggering a Printout 35
- Command Acknowledgment 35
- Additional Commands 35
- Ticket Memory 35
- Encode Binary Data on Track 1 36
- System Commands 37
- Document Entry Commands 38
- Print-data Commands 38
- Storage Commands 39
- Command Reference 41
- !Z 20 <CR><LF> 44
- Feed- acceleration and speed 45
- Example • 45
- Error code Error 47
- Print Related Commands 49
- Text Printing 50
- Graphics Printing 51
- Printing Bar Codes 53
- Example 2 • Code 39 example 54
- Example 3 • Code 128 example 54
- Canceling a Ticket 55
- Encoding 57
- Checksum 59
- Reading and Decoding 60
- What Can You Encode? 61
- Font Loading 68
- Logotypes 69
- Ticket Examples 70
- Printing Bold Text 73
- Reversed Text 73
- Text Attributes 74
- Default Parameter Settings 75
- Default Value 76
- Examples 76
- Summary of Parameter Settings 77
- Restore Factory Default 78
- Parameter Reference 79
- Sets burn time 27 80
- Silent 80
- Enabled 80
- Sets 400 steps/second 82
- Sets 4000 steps/second 82
- Sets 1000 steps/second 82
- Error Codes and Status 87
- Reporting 87
- ENQ” (05H), and !S commands 88
- Security Additions 89
- Extended acknowledgement 91
- Maintenance 93
- Fault Finding 94
- Cleaning the Print Head 95
- Firmware 95
- Setup Options 98
- Communications Protocol 98
- Communications Cable 99
- Ticket Base Material 100
- Coating and Preprint 101
- Magnetic Media 101
- Document Stock 102
- Specifications 102
- TTPM3 Accepted Sizes 103
- Equal Distance Between Tabs 104
- Tickets with 45° Cut Corners 105
- Firmware Versions 106
- Firmware History 106
- FW Version TTPM2 TTPM3 106
- FW revision Change 106
Powiązane produkty i podręczniki dla Drukuj i skanuj Zebra TTPM3
Drukuj i skanuj Zebra EM 220 Dokumentacja
(67 strony)
(67 strony)
Drukuj i skanuj Zebra 105Se Dokumentacja
(110 strony)
(110 strony)
Drukuj i skanuj Zebra CPCL Dokumentacja
(70 strony)
(70 strony)
Drukuj i skanuj Zebra TTPM2 Dokumentacja
(140 strony)
(140 strony)
(86 strony)
Drukuj i skanuj Zebra CPCL Dokumentacja
(497 strony)
(497 strony)
Drukuj i skanuj Zebra MZ series Dokumentacja
(53 strony)
(53 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.061 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji